sE Electronics X1 A Studijas kondensatora mikrofons

Studio Condenser Microphone for Vocals, Instruments, and Project Studios

Built for project studios, bedroom producers, and home recordists, the sE Electronics X1 A is a large-diaphragm condenser microphone with a newly developed back-electret capsule. It delivers a well-balanced frequency response for vocals, acoustic guitar, drum overheads, and amplified instruments. A cardioid polar pattern focuses on the source while keeping room ambience out of the recording. This model is the right choice for anyone who wants a single do-it-all condenser that performs well across an entire session.

What Sets This Microphone Apart in the Entry-Level Tier

Two on-body switches give flexibility most condensers at this price skip. The -20 dB pad extends dynamic range for close-miked guitar cabinets, brass, and kick drums, while the 100 Hz low-cut filter at 6 dB per octave cleans up rumble and proximity-effect boom. An integrated windscreen built into the headbasket removes the need for a separate pop filter on most vocal sessions, and the gold-plated 3-pin XLR connector keeps the signal path stable over years of use.

Capsule Design and Polar Pattern — Capture Detail With Control

The design pairs a 2/3" back-electret capsule with a fixed cardioid pickup that prioritizes on-axis detail. Cardioid rejection at the sides and rear helps isolate a single source in untreated rooms, which is exactly where most home recordists work. Fixed patterns mean no multi-pattern complexity to dial in — just point, set gain, and record.

• The 2/3" back-electret condenser capsule captures transients with speed and accuracy.
• Polar Pattern: Cardioid — focuses on the source while rejecting room bleed

Maximum SPL and Dynamic Range — Loud Sources Without Distortion

Headroom matters whenever a microphone faces a snare drum, a loud guitar cab, or a brass section at close range. With the -20 dB pad engaged, the sE Electronics X1 A tolerates up to 150 dB SPL at 0.5% THD, leaving plenty of margin for the loudest sources in a typical session. Dynamic range stretches from 114 dB without the pad to 134 dB with it engaged, so quiet whispers and loud peaks both sit well above the noise floor.

• Max SPL: 130 / 150 dB (0 / 20 dB pad, 0.5% THD @ 1 kHz)
• Dynamic Range: 114 / 134 dB (0 / 20 dB attenuation pad)
• The equivalent noise level is 16 dB (A-weighted), making it quiet enough for intimate vocals and acoustic sources.

Frequency Response, Powering, and Physical Build

Covering 20 Hz to 20 kHz, the frequency response is balanced and less top-heavy than many competing condensers near this price. Running on standard 48 V phantom power (P48 per IEC 61938) and drawing only 4.0 mA, this microphone pairs cleanly with any audio interface or mixer. The all-metal chassis rejects electrical interference, and the included swivel mic clip plus thread adapter fit common mic stands right out of the box.

• Frequency Range: 20 Hz – 20 kHz — covers the full audible spectrum with a balanced, non-hyped curve
• Sensitivity: 20 mV/Pa (-34 dBV)
• Powering: 48 V phantom power (P48, IEC 61938), 4.0 mA draw — works with any interface or mixer that supplies phantom power
• Connectivity: 3-pin male XLR, gold-plated
• Dimensions & Weight: 58 mm × 169 mm, 390 g — light enough for boom arms, solid enough for desk stands
• Package Contents: microphone, swivel mic clip (holder), mic stand thread adapter

Who Should Choose This Instrument

Home recordists, project-studio engineers, podcasters, and singer-songwriters will find this microphone handles vocals, acoustic guitar, drum overheads, and amplified instruments without compromise. Switchable pad and filter controls make it equally useful for loud close-miked sources and quiet acoustic work. Beginners benefit from the forgiving cardioid pattern and built-in windscreen, while experienced engineers appreciate the low self-noise and high SPL headroom at this price tier. Pair it with a shock mount and a basic audio interface for a complete tracking setup.

The X1 Line — A 2010 Redesign That Still Sets the Benchmark

When the brand introduced the original version in 2010, it redefined what an affordable large-diaphragm condenser could sound like, competing with microphones costing several times as much. This model continues that lineage with a new acoustic design, upgraded capsule and electronics, and the same rugged metal chassis as the rest of the X1 series.